How We Made $200 Vinyl DIY RV Skirting for Winter
This post may contain affiliate links.
If you are living in an RV in a cold climate, RV skirting is a MUST. Here is how we did our $200 DIY RV skirting.
RV Skirting Options
There are many options for skirting your RV. After researching the options available for our 5th wheel skirting, we found they pretty much boiled down to these:
- Custom RV skirting. ($$$$) Some companies will come to you, and some require you to travel to them. Either way, this option is great quality, but it’s also the most expensive option. It usually requires drilling holes along the bottom of your RV to install the snaps or channels for hanging the skirting.
- An inflatable AirSkirt. ($$$) An AirSkirt is an inflatable skirting made from heavy-duty vinyl that is inflated by an electric pump and is held in place by pressure. It doesn’t require drilling holes or using any adhesives. It’s designed to be easy to take down, transport, and put back up, so is a great option for people who need to move frequently instead of staying in one place all winter.
- EZ Snap RV skirting. ($$) This self-installed skirting kit is popular with many RVers, but reading about it left me wondering if I could make the same thing for less.
- DIY RV skirting. ($) This can be made from various materials including:
- Plywood or particle board. Sturdy and warm, but not cheap to pay for all that lumber, and not easy to install, remove, or transport.
- Foam board insulation. Sturdy and warm, easy to install, could possibly be transported, but not very environmentally friendly. However, it costs about $100 for skirting an entire RV. Read this tutorial for how to create your own foam board skirting.
- Plastic. Cheap, but not as sturdy. Also, not very environmentally friendly, and installation presents some challenges.
- Vinyl (What we chose!) I ended up choosing vinyl skirting because I hoped to be able to re-use it, and because it’s the time-tested choice of most professional skirting companies. I purchased billboard tarp vinyl, which is essentially a reused billboard (more details below).
Not sure which one to choose? Read this: RV Skirting Solutions for Every Budget
What type of vinyl is good for DIY RV skirting?
Some RV owners use insulated tarps to make RV skirting. At first, I was thinking along the same lines, that thicker is better. But then I learned that R-value isn’t necessarily the most important factor when it comes to RV skirting. The insulation actually comes more from trapping air underneath the RV than from the thickness of the vinyl.
Since insulated tarps are more expensive and much heavier, I decided the thinner vinyl would be fine. In the end, I chose to use 11 mil billboard tarp vinyl (these are recycled billboards!). This is the same type of vinyl used by many custom RV skirting companies.
However, it’s worth noting that this skirting setup was for insulating against temperatures below freezing but above zero. If you will be RVing in a climate where temperatures stay in the single digits or below zero for extended periods of time, you may want to consider a thicker material, such as insulated tarps or rigid foam board, as discussed later on in this article.
Read next: How to Stay Warm in a Cold Camper
You may also want to purchase a remote wireless thermometer so that you can accurately monitor the temperature under your RV and wherever your pipes and water lines are located. This will tell you with certainty how well your RV skirting is working, and whether you need to supplement with a light or space heater under your RV.
- 【Connect Note】 Pls install the station battery first, then install the sensor battery. If a specific channel is lost, press the CHANNEL/+ button until the channel indication single flashing.Verify the humidity sensors match closely with the console and the sensors are in the same location (about 1-3 meters apart). The sensors should agree within 10% (the accuracy is ± 5%). Allow about 30 minutes for all sensors to stabilize.
The billboard tarp vinyl company I ordered my vinyl from offers two color choices: Black or White.
Since making my skirting, I’ve found out about other companies, such as CoversAndAll.com, that sell new vinyl tarps in a variety of colors pre-cut to the exact sizes you need. They will even add grommets, D-rings, or loops along the edges if you want them to. In hindsight, this would save you a LOT of time. I would recommend it.
How We Made Our Vinyl RV Skirting
Supply List:
Below are the supplies we used along with what we paid for them at the time.
- Vinyl tarp material, enough to skirt our 38-foot fifth wheel, including the gooseneck and three of its four slides: $92.27 We used 11 mil weight billboard tarp vinyl purchased from BillboardTarps.com.
- Brass tarp grommets & grommet tool. This set came with 500 grommets, and that was way more than enough. Last year we didn’t use a grommet tool, just a cheap tool and dye with a hammer, and the task was much more difficult and time-consuming. This handheld grommet punch made this job one thousand percent faster and easier. Both the grommets and grommet punch cost us $42.48. Well worth it.
- Steel tent stakes. We ended up needing about 75, which cost around $30.
- Clear adhesive hooks. We used 65 for our 37-foot fifth wheel.
- One garment bag (optional) $10.99
- Duct tape (less than $10)
Total for the project: $213.45
I got a quote from a local guy for $1,600 to create skirting for our fifth wheel. Yikes! If you’ve priced professionally made trailer skirting, you know that $213 is a great deal.
Determining how much vinyl to order
To figure out how much vinyl to buy, I measured the total distance around the RV (including slides and gooseneck) as well as the height from the ground to the top of where the skirting would need to come, and then I ordered tarps that were either already the correct height, or else double the height and could be cut in half lengthwise to the correct height.
There was a lot of math involved, and I recommend drawing out the pieces you need and how you’ll cut them on a piece of paper.
Measure twice and cut once, as they say!
Overview of the RV Skirting Installation Process
Here’s a quick video overview of the process:
Cutting the Billboard Tarp Vinyl
This is what the billboard vinyl looks like all laid out. It literally used to be a billboard. The black side is the back; the other side of this piece had a Cracker Barrel billboard printed on it.
The first thing we did was to cut the vinyl into the sizes we needed. Calculate and measure carefully!
Last year I made a few mistakes in my calculations and we ended up having to order more vinyl, which meant paying double in shipping charges. 😬
The vinyl cuts easily with scissors. We cut this piece in half lengthwise to make two long pieces of skirting.
Applying the Adhesive Hooks
Below you can see the adhesive hooks on our RV leftover from last year’s DIY skirting.
(When we put them on I wasn’t thinking about how the ones on the sides of the slides would interfere with bringing the slides in. If we need to bring the slides in, we will obviously need to remove those hooks.)
As you can see, we opted for placing the hooks as frequently as possible. Since the hooks are cheap, we wanted to ensure that our skirting would be secure enough to not be blown away in storms and trap as much air as possible under the RV.
These hooks are extremely sturdy. I considered removing mine over the summer and had to use pliers to pull one off. It was so difficult to remove I gave up on the project and kept the hooks up for the next winter.
However, once the hook was removed, there was no damage or residue left behind on the fiberglass part of the RV. If you do want to remove your adhesive hooks, an inexpensive heat gun and plastic putty knife should remove them easily. Goo Gone is also great for any residue left behind!
Alternatives to the Adhesive Hooks
If you’re thinking about doing this project but don’t like the idea of using adhesive hooks, I have seen some people who used heavy duty Velcro instead…but I don’t really see how that would be any better since it is also adhesive.
Velcro is also more expensive than hooks. It does have the advantage of forming a seal all along the top of the skirting, whereas our skirting has small gaps at the top that may allow some of the warm air to escape.
Some people have also made their own vinyl skirting and hung it with adhesive snaps. That many snaps quickly get pricey (IMO), but that is an option, though not without some problems to anticipate. I am thinking about ordering some adhesive snaps for the area covering our propane tank access doors, though, so we can easily refill our propane tanks.
- Made from black poly-carbonate
Another alternative might be acrylic mounting tape to stick the same hooks to the slides. This tape stays put in cold weather (as I explained in this blog post) yet it is very easy to remove. I might even suggest trying it for all of the hooks if you’re concerned about the hooks being difficult to remove later, especially since the clear hooks do turn yellow in the sunlight over time.
DON’T Try These Alternatives for Hanging RV Skirting
Last year we originally tried hanging our skirting with heavy-duty suction cups, but even after following all of the instructions for using them (cleaning the area, applying in temperatures above freezing, etc.) they wouldn’t stay stuck. So after attempting a few options, I highly recommend the adhesive hooks we ended up using.
Below is why you don’t use duct tape on your RV! I learned the hard way.
We used Gorilla duct tape for some of the tricky spots last year, and it left quite a mess.
If I need to use tape on my RV in the future I will use foil HVAC tape as it can withstand any temperature and supposedly comes off cleanly.
- Aluminum Duct Tape - Impresa's high-quality and tensile strength aluminum tin foil tape is coated in epoxy resin that features strong, cold-weather solvent acrylic adhesive set on a easy-release silicone paper liner to preserve the adhesive
Installing the Grommets
Here’s what the skirting looks like hung from the hooks with a grommet. We folded the top of the vinyl over about four inches to make it sturdier and make it look neater.
With our hooks already hung, we used the grommet punch to punch holes as we hung it—no marking or measuring required. This method was significantly easier than measuring or marking where to add grommets. And it was worth the low cost of the east-to-use grommet punch!
We also used grommets along the bottom of the vinyl along with the tent stakes to keep the skirting in place. Sometimes this skirting with the tent stakes along the bottom comes unhooked in a few places and has to be rehung after very strong winds, but it does a much better job of staying put than alternatives, like the year we used water jugs to secure the bottom.
If a grommet rips the vinyl or pulls out of its hole, I plan to use black Gorilla duct tape to cover and reinforce the torn places and then redo those grommets. To prevent this from happening, I would suggest that you really make sure your grommets are tight and possibly reinforce the holes with a piece of black duct tape before you punch them.
Fastening the Skirting Along the Bottom
After we got the skirting hung along the top, we went around the bottom punching holes and pounding in tent stakes.
By now you can see how buying pre-cut vinyl with grommets already added would have saved us a lot of time!
Going Around Tricky Areas
We cut and folded the skirting to go around vents and other things we didn’t want to cover.
How We Joined the Seams Between Two Pieces of Vinyl
For the seams between pieces, we overlapped them by several feet.
Last year we tried using Gorilla duct tape to tape the seams together and it did not stay. It ended up coming untaped, blowing around in the wind, and making a sticky, dirty mess.
Overlapping the skirting without actually joining it worked just fine this time because we fastened each piece to the RV and to the ground. If you are concerned about making a tight seal you may want to find a different way to join the seams (see the idea suggested at the end of this article).
I planned the seam in the photo below to be at the spot where our sewer hose connects so that it can be easily unhooked if we need to access that area.
Skirting the Stair Area
Going around the stairs was tricky. I ended up taking the vinyl across the front underneath them, then adding a second piece to line the area behind the steps, hung from adhesive hooks I stuck to the steel frame.
I decided to use a heavy-duty clear shower curtain (which already had grommets!) weighted down with a few bricks instead of tarp vinyl to line the area behind the steps because our cat loves to play under the RV.
Skirting Around the Fifth Wheel Gooseneck
The gooseneck of a fifth wheel can be where the most cold air and wind enter an RV. It demands the best skirting… And it’s the hardest to skirt.
Unfortunately, our skirting didn’t do much to prevent wind from entering through the walls, so it still got pretty cold even with the skirting. I ended up lining the walls of our closet with a type of foam wall covering for extra insulation.
Related: 6 Ways You Must Prepare Your RV For Winter
If I had it to do over again, rather than try to make my own skirting for the gooseneck area, I would just purchase a fifth wheel skirt like this:
- Fifth wheel skirt turns wasted space into a useful storage area under your fifth wheel overhang. Great for outdoor furniture,bikes and other gear.
Adding a zipper to access the storage area under the gooseneck
To access the front storage area without having to fully remove the skirting, I decided to add a zipper. Instead of buying a surprisingly expensive long zipper, I decided to surgically remove the zipper from an inexpensive garment bag. This is an extra-long garment bag designed for wedding dresses.
I ended up cutting more off the sides until I had about six inches of plastic on either side of the zipper. Two inches on either side of the zipper would have looked better. You need just enough to stick tape to.
Then I taped the zipper to the back of the skirting using extra wide Gorilla duct tape.
Next, I cut a hole in the front of the skirting over the zipper.
And now I have a zipper opening for my skirting.
Here is our RV with its 5th-wheel skirting, all ready for cold weather!
Ideas from Other RV Owners
RV owner, Rob, allowed me to share photos of his skirting, along with some additional ideas he came up with:
Idea #1: Sandbags Used to Weight the Skirting Down on Concrete
Rob used sandbags from Amazon and filled them with sand from a local supplier to weigh down the skirting. Parked on a concrete pad, he couldn’t use tent stakes.
He says his skirting was able to withstand a wind gust recorded nearby at 52 mph without even budging! (Other RVers use pieces of lumber to weigh down their skirting.)
Idea #2: Snaps Used to Join the Skirting at the Seams
Rob used snaps and a snap tool to attach the skirting pieces to each other. I love this idea!
If you don’t mind screwing into your camper, you could also use screw-in snaps to hang the skirting. I was too afraid I would make a mistake and end up with a bunch of holes in my RV. But Rob’s turned out great!
Idea #3: Skirting Over the Stairs and Adding a Porch
Rob avoided the tricky issue of how to skirt around the steps! He folded in his steps and covered them by building these steps using free pallet wood instead.
I think Rob’s skirting looks really sharp!
Idea for Creating Access to Storage and Mechanical Components
Here’s another idea from an RV owner named Guy Hoffman. He went ahead and covered his storage access doors with skirting but created a flap that opens for access and stays closed with the use of magnets.
If you end up making your own skirting and come up with any more great ideas to share, or if you have any questions for me about our skirting, please leave a comment below! 🙂
Looking for a cheaper option? Consider foam board!
The project was actually easier and cheaper than the vinyl skirting ($106 plus tax for materials) and we like how it ended up looking. I wrote an in-depth tutorial detailing the process, which you can read here. We also made a video to demonstrate the process as we made the skirting:
Ashley Mann spent three years living full time in a 38-foot, 5th-wheel RV with her husband Josiah and their cat, Kitty. Her favorite thing about RV life is the challenge of finding the perfect way to organize a space, and she loves seeing all the creative and clever ways people come up with to customize their RVs.
With the foam board skirting how did you work around the black tank lever and needing access to it to dump? Both skirting options look very good btw.
Our black tank dump lever is accessed inside one of our storage bays. The only dump lever underneath our RV is for our galley tank, and we just leave it open except occasionally to treat & clean it. However, with the foam skirting I did create a removable panel to access our water shutoff. I’ve thought about doing something fancy with Velcro, but at this point I just kind of fold it back along one edge that’s taped and wedge it back into place to close it. Hope that helps!
Great ideas! I’ll be wintering in Texas this year and was wondering if I should skirt my trailer. I’m definitely going to look further into this.
As a side note, you can remove that duct tape adhesive with WD40. Spray and let sit. Rub off. Treat again, if needed. Had to do this with my front loader washer, as hubby put duct tape on it to keep the back door from scratching it when opened too far. Unfortunately, it left behind dried residue when I removed the tape. It took three soakings with WD40, but it all came off, without damaging the surface.
Thank you for the tip! I will definitely give it a try (one of these days, ha)!
We did foam board last year. Going to try the vinyl this year. I was wondering which skirting kept the RV the warmest?
We have never put a thermometer under the RV so I can’t say for sure, but my guess would be the foam board because it sealed off drafts better and was thicker too. If we lived farther north foam board would probably be my choice for a stationary winter, but the main advantage to the vinyl is that it’s easier to transport if necessary.
Hi Ashley,
Last year I used Reflectix insulation near Fort Leavenworth. You know the wind in Kansas is crazy so I had to do some repairs throughout the winter. Overall I was warm and had liquid water.
I’m back in Kansas for the winter but near Fort Riley. I remembered reading your billboard vinyl post last year. I was pleased to see the foam board you used when I looked up the article. I am going to try it. What thickness did you use?
Thank you so much for your advice. It has been quite helpful.
Rhonda
Hi Rhonda, I chose the 1″ thick foam board as it seemed sturdier than the thinner type yet was plenty warm once it was all sealed up.
Just an additional note, boat shrink vinyl is super heavy duty, comes in white, and zippered access doors are available for them, as well as vents. It lasts a very long time when exposed to the elements. I used it to cover a gazebo, lasted for 5 years. Heat shrink tape that’s uv resistant goes well with it. Here’s a link to the boat shrink vinyl on eBay.
This is a great tip! Thank you!
Why wasn’t the vinyl allowed in the park? thinking for future stays I’d like to know what problem they had with it that they didn’t have with foam boards?
The reason they gave us was that it looked tacky. And apparently they don’t think the foam boards look tacky.
Ashley, What kind of results did you get with removing the silver tape being on the outside of the RV? I’ve used it lots of times on one thing or another but never on the outside of my RV. I have a new 5th wheel now and sure don’t wanna mess it up.
I’m headed to Coffeyville, KS soon for work and being from that general area (the Oklahoma panhandle) I know what winters are like in that part of the country. COLD and windy!!
I already have some white duct tape for the foam itself.
Did I see you post that you had actually taped a piece of foam directly under your slides? Like right to the bottom of the slide floor? Great idea!!
Your vlog is great. I’m subscribing 🙂 Kelli
Yes, I taped the foam to the bottom of the slide floor! 🙂 My experience with the tape is that it can be used on fiberglass without damaging it at all, but that if you put it on areas with paint it’s possible to damage the paint when pulling it off, but as long as you pull it off very carefully and slowly you can pull it off with no damage. And it’s definitely less likely to damage paint than any other type of tape or adhesive, which is why I use and recommend it. Still, mistakes can happen even when you’re being careful so if a nick in your paint is something you would be very upset about you probably want to avoid sticking anything to your RV exterior whatsoever.
I appreciate your response Ashley! I got to thinking though… I could make it easier to remove just by taking a blow drier to it or some hot water. Boil some water in the teapot,pour it on slowly and grab it with tweezers. Where there’s a will…😉
Yes, that might help it come off more cleanly. Also, if you can wait until a warm, sunny day to take it off, that would probably accomplish the same thing. If you buy some of the tape and test it in an inconspicuous area you can get a better idea of what it’s like to use. Good luck!