How We Made $200 Vinyl DIY RV Skirting for Winter

|

This post may contain affiliate links.

If you are living in an RV in a cold climate, RV skirting is a MUST. Here is how we did our $200 DIY RV skirting.

RV Skirting Options

There are many options for skirting your RV. After researching the options available for our 5th wheel skirting, we found they pretty much boiled down to these:

  • Custom RV skirting. ($$$$) Some companies will come to you, and some require you to travel to them.  Either way, this option is great quality, but it’s also the most expensive option. It usually requires drilling holes along the bottom of your RV to install the snaps or channels for hanging the skirting.
  • An inflatable AirSkirt. ($$$) An AirSkirt is an inflatable skirting made from heavy-duty vinyl that is inflated by an electric pump and is held in place by pressure. It doesn’t require drilling holes or using any adhesives.  It’s designed to be easy to take down, transport, and put back up, so is a great option for people who need to move frequently instead of staying in one place all winter.
  • EZ Snap RV skirting. ($$) This self-installed skirting kit is popular with many RVers, but reading about it left me wondering if I could make the same thing for less.
  • DIY RV skirting. ($) This can be made from various materials including:
    • Plywood or particle board. Sturdy and warm, but not cheap to pay for all that lumber, and not easy to install, remove, or transport.
    • Foam board insulation. Sturdy and warm, easy to install, could possibly be transported, but not very environmentally friendly. However, it costs about $100 for skirting an entire RV. Read this tutorial for how to create your own foam board skirting.
    • Plastic. Cheap, but not as sturdy.  Also, not very environmentally friendly, and installation presents some challenges.
    • Vinyl (What we chose!) I ended up choosing vinyl skirting because I hoped to be able to re-use it, and because it’s the time-tested choice of most professional skirting companies. I purchased billboard tarp vinyl, which is essentially a reused billboard (more details below).

Not sure which one to choose? Read this: RV Skirting Solutions for Every Budget

What type of vinyl is good for DIY RV skirting?

Some RV owners use insulated tarps to make RV skirting. At first, I was thinking along the same lines, that thicker is better. But then I learned that R-value isn’t necessarily the most important factor when it comes to RV skirting. The insulation actually comes more from trapping air underneath the RV than from the thickness of the vinyl.

Since insulated tarps are more expensive and much heavier, I decided the thinner vinyl would be fine. In the end, I chose to use 11 mil billboard tarp vinyl (these are recycled billboards!). This is the same type of vinyl used by many custom RV skirting companies.

However, it’s worth noting that this skirting setup was for insulating against temperatures below freezing but above zero. If you will be RVing in a climate where temperatures stay in the single digits or below zero for extended periods of time, you may want to consider a thicker material, such as insulated tarps or rigid foam board, as discussed later on in this article.

Read next: How to Stay Warm in a Cold Camper

You may also want to purchase a remote wireless thermometer so that you can accurately monitor the temperature under your RV and wherever your pipes and water lines are located. This will tell you with certainty how well your RV skirting is working, and whether you need to supplement with a light or space heater under your RV.

Sale
ORIA Indoor Outdoor Thermometer, Digital Hygrometer Thermometer, Wireless Temperature and Humidity Gauge Monitor with 3 Sensors, LCD Backlight for Home, Office, Bedroom, White
  • 【Connect Note】 Pls install the station battery first, then install the sensor battery. If a specific channel is lost, press the CHANNEL/+ button until the channel indication single flashing.Verify the humidity sensors match closely with the console and the sensors are in the same location (about 1-3 meters apart). The sensors should agree within 10% (the accuracy is ± 5%). Allow about 30 minutes for all sensors to stabilize.

The billboard tarp vinyl company I ordered my vinyl from offers two color choices: Black or White. 

Since making my skirting, I’ve found out about other companies, such as CoversAndAll.com, that sell new vinyl tarps in a variety of colors pre-cut to the exact sizes you need. They will even add grommets, D-rings, or loops along the edges if you want them to. In hindsight, this would save you a LOT of time. I would recommend it.

How We Made Our Vinyl RV Skirting

Supply List:

Below are the supplies we used along with what we paid for them at the time.

  • Vinyl tarp material, enough to skirt our 38-foot fifth wheel, including the gooseneck and three of its four slides: $92.27  We used 11 mil weight billboard tarp vinyl purchased from BillboardTarps.com.
  • Brass tarp grommets & grommet tool. This set came with 500 grommets, and that was way more than enough. Last year we didn’t use a grommet tool, just a cheap tool and dye with a hammer, and the task was much more difficult and time-consuming. This handheld grommet punch made this job one thousand percent faster and easier. Both the grommets and grommet punch cost us $42.48. Well worth it.
  • Steel tent stakes. We ended up needing about 75, which cost around $30.
  • Clear adhesive hooks. We used 65 for our 37-foot fifth wheel.
  • One garment bag (optional) $10.99
  • Duct tape (less than $10)

Total for the project: $213.45

Materials used for making DIY RV skirting
Materials we used for hanging our DIY skirting

I got a quote from a local guy for $1,600 to create skirting for our fifth wheel. Yikes! If you’ve priced professionally made trailer skirting, you know that $213 is a great deal.

Determining how much vinyl to order

To figure out how much vinyl to buy, I measured the total distance around the RV (including slides and gooseneck) as well as the height from the ground to the top of where the skirting would need to come, and then I ordered tarps that were either already the correct height, or else double the height and could be cut in half lengthwise to the correct height.

There was a lot of math involved, and I recommend drawing out the pieces you need and how you’ll cut them on a piece of paper.

Measure twice and cut once, as they say!

Overview of the RV Skirting Installation Process

Here’s a quick video overview of the process:

Cutting the Billboard Tarp Vinyl

This is what the billboard vinyl looks like all laid out. It literally used to be a billboard. The black side is the back; the other side of this piece had a Cracker Barrel billboard printed on it.

Making RV skirting out of billboard tarp vinyl
Billboard vinyl ready to cut and make into RV skirting

The first thing we did was to cut the vinyl into the sizes we needed. Calculate and measure carefully! 

Last year I made a few mistakes in my calculations and we ended up having to order more vinyl, which meant paying double in shipping charges. 😬

The vinyl cuts easily with scissors. We cut this piece in half lengthwise to make two long pieces of skirting.

Applying the Adhesive Hooks

Below you can see the adhesive hooks on our RV leftover from last year’s DIY skirting. 

Clear adhesive hooks used to hang RV skirting made from billboard tarp vinyl

(When we put them on I wasn’t thinking about how the ones on the sides of the slides would interfere with bringing the slides in. If we need to bring the slides in, we will obviously need to remove those hooks.)

As you can see, we opted for placing the hooks as frequently as possible. Since the hooks are cheap, we wanted to ensure that our skirting would be secure enough to not be blown away in storms and trap as much air as possible under the RV.

These hooks are extremely sturdy. I considered removing mine over the summer and had to use pliers to pull one off. It was so difficult to remove I gave up on the project and kept the hooks up for the next winter.

However, once the hook was removed, there was no damage or residue left behind on the fiberglass part of the RV. If you do want to remove your adhesive hooks, an inexpensive heat gun and plastic putty knife should remove them easily. Goo Gone is also great for any residue left behind!

Alternatives to the Adhesive Hooks

If you’re thinking about doing this project but don’t like the idea of using adhesive hooks, I have seen some people who used heavy duty Velcro instead…but I don’t really see how that would be any better since it is also adhesive.

Velcro is also more expensive than hooks. It does have the advantage of forming a seal all along the top of the skirting, whereas our skirting has small gaps at the top that may allow some of the warm air to escape.

Some people have also made their own vinyl skirting and hung it with adhesive snaps. That many snaps quickly get pricey (IMO), but that is an option, though not without some problems to anticipate. I am thinking about ordering some adhesive snaps for the area covering our propane tank access doors, though, so we can easily refill our propane tanks.

FIA HK104 Stick- A-Stud Hardware Kit
327 Reviews
FIA HK104 Stick- A-Stud Hardware Kit
  • Made from black poly-carbonate

Another alternative might be acrylic mounting tape to stick the same hooks to the slides. This tape stays put in cold weather (as I explained in this blog post) yet it is very easy to remove. I might even suggest trying it for all of the hooks if you’re concerned about the hooks being difficult to remove later, especially since the clear hooks do turn yellow in the sunlight over time.

DON’T Try These Alternatives for Hanging RV Skirting

Last year we originally tried hanging our skirting with heavy-duty suction cups, but even after following all of the instructions for using them (cleaning the area, applying in temperatures above freezing, etc.) they wouldn’t stay stuck. So after attempting a few options, I highly recommend the adhesive hooks we ended up using.

Suction cup used to hang RV skirting - didn't work.

Below is why you don’t use duct tape on your RV! I learned the hard way. 

Why you shouldn't stick duct tape to your RV

We used Gorilla duct tape for some of the tricky spots last year, and it left quite a mess.

If I need to use tape on my RV in the future I will use foil HVAC tape as it can withstand any temperature and supposedly comes off cleanly.

IMPRESA - Aluminum Foil Tape for Sealing and Patching Hot and Cold HVAC, Ducts, Pipes - Insulation Home and Commercial - 1.9 Inches Wide (150 Feet/50 Yards)
5,211 Reviews
IMPRESA - Aluminum Foil Tape for Sealing and Patching Hot and Cold HVAC, Ducts, Pipes - Insulation Home and Commercial - 1.9 Inches Wide (150 Feet/50 Yards)
  • Aluminum Duct Tape - Impresa's high-quality and tensile strength aluminum tin foil tape is coated in epoxy resin that features strong, cold-weather solvent acrylic adhesive set on a easy-release silicone paper liner to preserve the adhesive

Installing the Grommets

Here’s what the skirting looks like hung from the hooks with a grommet. We folded the top of the vinyl over about four inches to make it sturdier and make it look neater.

Clear adhesive hooks and grommets used to hang RV skirting made from billboard tarp vinyl

With our hooks already hung, we used the grommet punch to punch holes as we hung it—no marking or measuring required. This method was significantly easier than measuring or marking where to add grommets. And it was worth the low cost of the east-to-use grommet punch!

Making DIY RV skirting
Adding grommets along the top of the skirting – the fast way

We also used grommets along the bottom of the vinyl along with the tent stakes to keep the skirting in place. Sometimes this skirting with the tent stakes along the bottom comes unhooked in a few places and has to be rehung after very strong winds, but it does a much better job of staying put than alternatives, like the year we used water jugs to secure the bottom.

If a grommet rips the vinyl or pulls out of its hole, I plan to use black Gorilla duct tape to cover and reinforce the torn places and then redo those grommets. To prevent this from happening, I would suggest that you really make sure your grommets are tight and possibly reinforce the holes with a piece of black duct tape before you punch them.

Grommet ripped hole in vinyl

Fastening the Skirting Along the Bottom

After we got the skirting hung along the top, we went around the bottom punching holes and pounding in tent stakes.

Making DIY 5th wheel skirting out of billboard tarp vinyl

By now you can see how buying pre-cut vinyl with grommets already added would have saved us a lot of time!

Homemade DIY RV trailer skirting from billboard tarp vinyl for around $200 to get ready for cold weather winter camping
Tent stake securing the skirting along the bottom

Going Around Tricky Areas

We cut and folded the skirting to go around vents and other things we didn’t want to cover.

How We Joined the Seams Between Two Pieces of Vinyl

For the seams between pieces, we overlapped them by several feet. 

Last year we tried using Gorilla duct tape to tape the seams together and it did not stay. It ended up coming untaped, blowing around in the wind, and making a sticky, dirty mess. 

Overlapping the skirting without actually joining it worked just fine this time because we fastened each piece to the RV and to the ground. If you are concerned about making a tight seal you may want to find a different way to join the seams (see the idea suggested at the end of this article). 

I planned the seam in the photo below to be at the spot where our sewer hose connects so that it can be easily unhooked if we need to access that area.

Where two pieces of skirting are joined
Two pieces of skirting joined where they can easily be unhooked for access to the sewer hose

Skirting the Stair Area

Going around the stairs was tricky. I ended up taking the vinyl across the front underneath them, then adding a second piece to line the area behind the steps, hung from adhesive hooks I stuck to the steel frame.

Skirting the stair area
Skirting the stair area

I decided to use a heavy-duty clear shower curtain (which already had grommets!) weighted down with a few bricks instead of tarp vinyl to line the area behind the steps because our cat loves to play under the RV. 

Kitty under the RV
Kitty under the RV

Skirting Around the Fifth Wheel Gooseneck

The gooseneck of a fifth wheel can be where the most cold air and wind enter an RV. It demands the best skirting… And it’s the hardest to skirt.

Fifth wheel skirting
Skirting around the fifth wheel gooseneck

Unfortunately, our skirting didn’t do much to prevent wind from entering through the walls, so it still got pretty cold even with the skirting. I ended up lining the walls of our closet with a type of foam wall covering for extra insulation.

Related: 6 Ways You Must Prepare Your RV For Winter

If I had it to do over again, rather than try to make my own skirting for the gooseneck area, I would just purchase a fifth wheel skirt like this:

Adco (3502) Polar White 64' High x 266' Length 5TH Wheel Skirt
471 Reviews
Adco (3502) Polar White 64" High x 266" Length 5TH Wheel Skirt
  • Fifth wheel skirt turns wasted space into a useful storage area under your fifth wheel overhang. Great for outdoor furniture,bikes and other gear.

Adding a zipper to access the storage area under the gooseneck

To access the front storage area without having to fully remove the skirting, I decided to add a zipper. Instead of buying a surprisingly expensive long zipper, I decided to surgically remove the zipper from an inexpensive garment bag. This is an extra-long garment bag designed for wedding dresses.

Use a zipper from a garment bag to make a door in RV skirting

I ended up cutting more off the sides until I had about six inches of plastic on either side of the zipper. Two inches on either side of the zipper would have looked better. You need just enough to stick tape to.

Use a zipper from a garment bag to make a door in RV skirting

Then I taped the zipper to the back of the skirting using extra wide Gorilla duct tape.

Back of the zipper

Next, I cut a hole in the front of the skirting over the zipper.

Zipper made from garment bag added to RV skirting

And now I have a zipper opening for my skirting.

Zipper made from garment bag added to RV skirting

Here is our RV with its 5th-wheel skirting, all ready for cold weather!

Fifth wheel skirted with DIY vinyl RV skirting
Skirting complete!

Ideas from Other RV Owners

RV owner, Rob, allowed me to share photos of his skirting, along with some additional ideas he came up with:

Idea #1: Sandbags Used to Weight the Skirting Down on Concrete

Rob used sandbags from Amazon and filled them with sand from a local supplier to weigh down the skirting. Parked on a concrete pad, he couldn’t use tent stakes.

He says his skirting was able to withstand a wind gust recorded nearby at 52 mph without even budging!  (Other RVers use pieces of lumber to weigh down their skirting.)

DIY RV skirting made from billboard tarp vinyl, hung with adhesive hooks and weighted down with sandbags
RV skirting weighted down with sandbags – Photo by Rob Dodd

Idea #2: Snaps Used to Join the Skirting at the Seams

Rob used snaps and a snap tool to attach the skirting pieces to each other. I love this idea! 

If you don’t mind screwing into your camper, you could also use screw-in snaps to hang the skirting. I was too afraid I would make a mistake and end up with a bunch of holes in my RV. But Rob’s turned out great!

Idea #3: Skirting Over the Stairs and Adding a Porch

Rob avoided the tricky issue of how to skirt around the steps! He folded in his steps and covered them by building these steps using free pallet wood instead.

RV porch made from free pallet wood
RV with porch added – Photo by Rob Dodd

I think Rob’s skirting looks really sharp!

DIY RV skirting made from billboard tarp vinyl, hung with adhesive hooks and weighted down with sandbags
Photo by Rob Dodd

Idea for Creating Access to Storage and Mechanical Components

Here’s another idea from an RV owner named Guy Hoffman.  He went ahead and covered his storage access doors with skirting but created a flap that opens for access and stays closed with the use of magnets.

Use magnets to create a removable cover for access through RV skirting.
Photo by Guy Hoffman

If you end up making your own skirting and come up with any more great ideas to share, or if you have any questions for me about our skirting, please leave a comment below! 🙂

Looking for a cheaper option? Consider foam board!

The project was actually easier and cheaper than the vinyl skirting ($106 plus tax for materials) and we like how it ended up looking. I wrote an in-depth tutorial detailing the process, which you can read here. We also made a video to demonstrate the process as we made the skirting:

Share This With A Friend:

Similar Posts

81 Comments

  1. Hello!!
    We are going into cold weather and I had the same idea with, used sign vinyl. Then my wife said this couple has alot of the same ideas you do…haha..its true!! Love your post!!! What millimeter did you get? 11? 15? 17? So glad it works!! Thanks again!
    -Kermit

    1. Hi! 🙂 We used the 9 oz. / 11 mil vinyl last year and again this year. There were a couple of places last year where the vinyl wore through because the wind blew it up against a sharp corner, but hopefully that won’t happen this year since the skirting is staked down unlike last year. If it does, though, I will probably just patch it with black Gorilla tape.

      I think a few people have used the 20 mil pond liner, but I think the 9 oz does its job of blocking wind and keeping heat from escaping just fine for us, at least in Kansas City where we are located. It’s still pretty heavy, and when I ordered a sample of one of the professional skirting brands, the weight was comparable.

      One other thing I will mention is that there are a few places where the grommet pulled partway out of the hole punched in the skirting where I staked it down because it was pulled so tight by the tent stake, but I think that may have been more due to the grommet not having been squeezed tight enough rather than the weight of the vinyl.

  2. What size billboard tarp did you get? I see several different sizes and I’m unsure how to measure my travel trailer to know how much I need.

    1. I think you’re asking about the dimensions of the tarp I ordered rather than the weight, but just in case, we got the 9 oz / 11 mil weight. As for the dimensions, I ordered multiple pieces which I cut and spliced together. To figure out how much I needed, first I determined the height the skirting would need to be by measuring from the highest point, which for us was on the sides of our slides, and allowing a few inches to fold over on top and about a foot extra on the bottom to stake down. Instead of making it the same height all the way around (which many people do), we decided to make the skirting shorter where the cargo storage doors were located to avoid having to cut holes for access. Also I measured the piece for the gooseneck separately. After that I measured the length needed of each height by just walking around the RV with a tape measure. After I had the dimensions I needed, I looked for pieces to buy that had approximately double the height and half the length, planning to cut it in half lengthwise. Of course the exact dimensions will be different for each RV, but I find it helps to draw the tarp on a piece of paper and mark where it will be cut in order to figure out how much to buy without wasting too much. It can definitely make your brain hurt to figure it out. Hope that helps.

  3. Hey there! My wife and I are going to do this same thing as we have a friend who can hook us up with the billboard vinyl for free. Just wondering how much you used? How big was your billboard vinyl? We have a smaller camper than you guys at about 32′ so I would think whatever you all used would be sufficient for us. Thanks so much!

    1. This year I ordered two tarps, a 26’x10′ piece for the gooseneck, and a 47’x10′ piece which I cut into four pieces to make the rest. The dimensions of those four pieces were 47’x5′, 27’x5′, 10’x2.5′, and 10’x2.5′. The 10’x2.5 pieces were used for the front half (before the gooseneck) where we didn’t skirt up so high, but if you are in an extremely cold climate I might recommend going ahead and going up the full height because there is a bit of a gap along the bottom edge of our camper in that section that I’m sure allows some wind to get in.

      Last year I accidentally ordered too little skirting, and that is really frustrating, so I would suggest measuring to be sure you have enough. To determine how much you need, figure out how tall it needs to be at the highest point (don’t forget you might want to fold it over along the top edge and will want extra along the bottom), then measure the distance around the RV (including going around slides). I was able to find a piece to cut that was half the length and twice the height, plus a few extra feet for good measure.

      Good luck!

  4. Ok folks, I would like to try this idea but no one gave the website or contact information on where to buy the billboard sign tarps.

Leave a Reply

Your email address will not be published. Required fields are marked *